Apr 12, 2009 9:43 PM How to use strcpy in dev c windows 10. How to make sure little snitch blocks itself.
Hi and welcome to Discussions,
best I could find: Internal Microphone The internal microphone operates independently from all other audio input ports and is always available. The internal microphone supports recording at bit depths of 16, 20, or 24 bits per sample and at sample rates of 44.1 kHz, 48 kHz, or 96 kHz. Audio recorded from the microphone is presented as a stereo data stream with the same data appearing on both the left and right channels. The microphone gain can be adjusted from -16.0 dB to +30.0 dB. Line Input The line input operates independently from all other audio input ports and is always available. The line input supports recording at bit depths of 16, 20, or 24 bits per sample and at sample rates of 44.1 kHz, 48 kHz, or 96 kHz. Audio recorded from the line input is presented as a stereo data stream. The line input gain can be adjusted from 0.0 dB to +30 dB. During input of a 1 kHz, full-scale 1 VRMS sine wave (44.1 kHz input sample rate, 24-bit sample depth, 0.0 dB input gain, no weighting) the audio line input has the following nominal specifications: Jack type: 3.5 mm stereo Maximum input voltage: 1 VRMS (+2.22 dBu) Minimum voltage input for full scale output: 31 mVRMS (-27.95 dBu) at input gain = +30 dB Input impedance: > 20 kΩ Frequency response: 20 Hz to 20 kHz, +0.5 dB/-3 dB Signal-to-noise ratio (SNR): > 90 dB Total harmonic distortion + noise (THD+N): < -75 dB (0.02%) Channel separation: > 80 dB Optical Digital Input Based on playback of a 1 kHz, -1 dBFS 24-bit sine wave playback, 24-bit 44.1 kHz output sample rate (unless otherwise specified below) the digital audio input and output have the following electrical characteristics (nominal specifications): FSI – input sample rates: 44.1 kHz, 48 kHz, or 96 kHz Bits per sample: 16-bit or 24-bit Signal-to-noise ratio (SNR): > 130 dB Total harmonic distortion + noise (THD+N): < -130 dB (0.00003%) Output Ports The 15-inch MacBook Pro computer includes three audio output ports that can be used to play audio: internal speakers, combination line and headphone output, and S/PDIF optical digital output. Internal Speakers The internal speakers are automatically selected for audio output if no external device is detected at either the line/headphone output port or the S/PDIF optical digital output port. The internal speakers support a stereo data stream at bit depths of 16, 20, or 24 bits per sample and at sample rates of 44.1 kHz, 48 kHz, or 96 kHz. Line/Headphone Output The line/headphone output is automatically selected for audio output if no external device is detected at the S/PDIF optical digital output port. The line/headphone output supports a stereo data stream at bit depths of 16, 20, or 24 bits per sample and at sample rates of 44.1 kHz, 48 kHz, or 96 kHz. The line/headphone output volume can be adjusted from 0.0 dB to -95.25 dB. During playback of a 1 kHz, full-scale sine wave (44.1 kHz output sample rate, 24-bit sample depth, 100 kΩ load, unless otherwise specified) the audio line output has the following nominal specifications: Jack type: 3.5 mm stereo Maximum output voltage: 2 VRMS (+8.24 dBu) Output impedance: < 24 Ω Frequency response: 20 Hz to 20 kHz, +0.5 dB/-3 dB Signal-to-noise ratio (SNR): > 90 dB Total harmonic distortion + noise (THD+N): < -80 dB (0.01%) Channel separation: > 75 dB Note: For best results, equipment plugged into the line/headphone output jack should not connect the audio ground to other grounds, such as the chassis or “green-wire” ground. S/PDIF Optical Digital Output The S/PDIF optical digital output is automatically selected when a S/PDIF optical digital output external device is detected. The S/PDIF optical digital output supports a stereo data stream at bit depths of 16, 20, or 24 bits per sample and at sample rates of 44.1 kHz, 48 kHz or 96 kHz in PCM format. In addition, the S/PDIF optical digital output supports AC-3 encoded audio format. During playback of a 1 kHz, full-scale sine wave (S/PDIF output format, 44.1 kHz output sample rate, 24-bit sample depth, unless otherwise specified) the digital audio output has the following nominal specifications: Jack type: 3.5 mm optical Digital audio signal-to-noise ratio (SNR): > 130 dB Digital audio total harmonic distortion + noise (THD+N): < -130 dB (0.00003%) The S/PDIF optical output channel status conforms to IEC 60958-3 consumer mode digital audio. The audio output connector on the 15-inch MacBook Pro is a 3.5 mm electrical/optical combination (combo) jack. Hope it helps Stefan
Traktor Pro 2 Mac![]() Macbook Pro Sound Card Traktor 4 Channel 2
Voice machine processor vst download. Sep 01, 2019 No sound or volume coming from MacBook – How to Fix September 1, 2019 by luigi911 36 Comments If you have no sound coming through your MacBook, iMac, MacBook Pro and Air in OS X there are some simple fixes and solutions to resolve to this issue.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |